View ATA5756-6DPY_4285744.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* PLL Transmitter IC with Single-ended Output * High Output Power (6 dBm) at 8.1 mA (315 MHz) and 8.5 mA (433 MHz) Typical Values * Divide by 24 (ATA5756) and 32 (ATA5757) Blocks for 13 MHz Crystal Frequencies and
for Low XTO Start-up Times
* Modulation Scheme ASK/FSK with Internal FSK Switch * Up to 20 kBaud Manchester Coding, Up to 40 kBaud NRZ Coding * Power-down Idle and Power-up Modes to Adjust Corresponding Current Consumption
through ASK/FSK/Enable Input Pins
* ENABLE Input for Parallel Usage of Controlling Pins in a 3-wire Bus System * CLK Output Switches ON if the Crystal Current Amplitude has Reached 35% to 80% of * * * *
its Final Value Crystal Oscillator Time Until CLK Output is Activated, Typically 0.6 ms Supply Voltage 2.0 V to 3.6 V in Operation Temperature Range of -40C to +125C ESD Protection at all Pins (4 kV HBM) Small Package TSSOP10
UHF ASK/FSK Transmitter ATA5756 ATA5757
Benefits
* Low Parasitic FSK Switch Integrated * Very Short and Reproducible Time to Transmit Typically < 0.85 ms * 13.125 MHz/13.56 MHz Crystals Give Opportunity for Small Package Sizes
1. Description
The ATA5756/ATA5757 is a PLL transmitter IC which has been developed for the demands of RF low-cost transmission systems at data rates up to 20 kBaud Manchester coding and 40 kBaud NRZ coding. The transmitting frequency range is 313 MHz to 317 MHz (ATA5756) and 432 MHz to 448 MHz (ATA5757), respectively. It can be used in both FSK and ASK systems. Due to its shorten crystal oscillator settling time it is well suited for Tire Pressure Monitoring (TPM) and for Passive Entry Go applications.
Figure 1-1.
System Block Diagram
UHF ASK/FSK TPM and Remote control transmitter UHF ASK/FSK Remote control receiver
1 Li cell
ATA5756/ ATA5757
PLL Antenna Antenna XTO VCO
Keys
Encoder ATARx9x
U3741B/ U3745B/ T5743/ T5744/
Demod.
Control
1...3
C
IF Amp
PLL
XTO
Power amp.
LNA
VCO
4702J-RKE-09/08
2. Pin Configuration
Figure 2-1. Pinning TSSOP10
10
CLK ASK
1
ENABLE
2 ATA5756 ATA5757
9
GND
FSK
3
8
VS
ANT2
4
7
XTO1
ANT1
5
6
XTO2
Table 2-1.
Pin
Pin Description
Symbol Function Configuration
1
CLK
Clock output signal for the microcontroller. The clock output frequency is set by the crystal to fXTAL/8. The CLK output stays Low in power-down mode and after enabling of the PLL. The CLK output switches on if the oscillation amplitude of the crystal has reached a certain level.
VS
100 100 200k
CLK
ASK
50k
VRef = 1.1V
2
ASK
Switches on the power amplifier for ASK modulation and enables the PLL and XTO if the ENABLE pin is open
200k
20 A
FSK
200k
VRef = 1.1V
3
FSK
Switches off the FSK switch (switch has high Z if signal at pin FSK is High) and enables the PLL and the XTO if the ENABLE pin is open
5 A 200k
2
ATA5756/ATA5757
4702J-RKE-09/08
ATA5756/ATA5757
Table 2-1.
Pin 4
Pin Description (Continued)
Symbol ANT2 Function Emitter of antenna output stage
ANT1
Configuration
5
ANT1
Open collector antenna output
ANT2
6
XTO2
Diode switch, used for FSK modulation
(FSK < 0.25V) AND (ENABLE > 1.7V) XTO2
210 A
VS 1.5k 1.2k
VS
7
XTO1
Connection for crystal
XTO1
182 A
8 9
VS GND
Supply voltage Ground
See ESD protection circuitry (see Figure 4-9 on page 14) See ESD protection circuitry (see Figure 4-9 on page 14)
VS
ENABLE input If ENABLE is connected to GND and the ASK or FSK pin is High, the device stays in idle mode. In normal operation ENABLE is left open and ASK or FSK is used to enable the device.
30 A (FSK >1.7 V ) OR (ASK > 1.7 V)
ENABLE 150k
10
ENABLE
250k
3
4702J-RKE-09/08
Figure 2-2.
Block Diagram
ATA5756 / ATA5757
Power up/down CLK EN
f 8
ENABLE
1
10 f
ASK
24/ 32
GND
2
OR FSK
9
PFD VS
3
CP Ampl. OK ANT2
8
XTO1
XTO LF
4
7
EN ANT1 XTO2
PA
5
VCO
6
PLL
3. General Description
This fully integrated PLL transmitter allows the design of simple, low-cost RF miniature transmitters for TPM and RKE applications. The VCO is locked to 24 x f X T A L /32 x f X T A L for ATA 5 7 5 6 / ATA 5 7 5 7 . T h u s , a 1 3 . 1 2 5 M H z / 1 3 . 5 6 M H z c r y s t a l i s n e e d e d f o r a 315 MHz/433.92 MHz transmitter. All other PLL and VCO peripheral elements are integrated. The XTO is a series resonance (current mode) oscillator. Only one capacitor and a crystal connected in series to GND are needed as external elements in an ASK system. The internal FSK switch, together with a second capacitor, can be used for FSK modulation. The crystal oscillator needs typically 0.6 ms until the CLK output is activated if a crystal as defined in the electrical characteristics is used (e.g., TPM crystal). For most crystals used in RKE systems, a shorter time will result. The CLK output is switched on if the amplitude of the current flowing through the crystal has reached 35% to 80% of its final value. This is synchronized with the 1.64/1.69 MHz CLK output. As a result, the first period of the CLK output is always a full period. The PLL is then locked <250 s after CLK output activation. This means an additional wait time of 250 s is necessary before the PA can be switched on and the data transmission can start. This results in a significantly lower time of about 0.85 ms between enabling the ATA5756/ATA5757 and the beginning of the data transmission which saves battery power especially in tire pressure monitoring systems.
4
ATA5756/ATA5757
4702J-RKE-09/08
ATA5756/ATA5757
The power amplifier is an open-collector output delivering a current pulse which is nearly independent from the load impedance and can therefore be controlled via the connected load impedance. This output configuration enables a simple matching to any kind of antenna or to 50 . A high power efficiency for the power amplifier results if an optimized load impedance of ZLoad, opt = 380 + j340 (ATA5756) at 315 MHz and ZLoad, opt = 280 + j310 (ATA5757) at 433.92 MHz is used at the 3-V supply voltage.
4. Functional Description
If ASK = Low, FSK = Low and ENABLE = open or Low, the circuit is in power-down mode consuming only a very small amount of current so that a lithium cell used as power supply can work for many years. If the ENABLE pin is left open, ENABLE is the logical OR operation of the ASK and FSK input pins. This means, the IC can be switched on by either the FSK of the ASK input. If the ENABLE pin is Low and ASK or FSK are High, the IC is in idle mode where the PLL, XTO and power amplifier are off and the microcontroller ports controlling the ASK and FSK inputs can be used to control other devices. This can help to save ports on the microcontroller in systems where other devices with 3-wire interface are used. With FSK = High and ASK = Low and ENABLE = open or High, the PLL and the XTO are switched on and the power amplifier is off. When the amplitude of the current through the crystal has reached 35% to 80% of its final amplitude, the CLK driver is automatically activated. The CLK output stays Low until the CLK driver has been activated. The driver is activated synchronously with the CLK output frequency, hence, the first pulse on the CLK output is a complete period. The PLL is then locked within <250 s after the CLK driver has been activated, and the transmitter is then ready for data transmission. With ASK = High the power amplifier is switched on. This is used to perform the ASK modulation. During ASK modulation the IC is enabled with the FSK or the ENABLE pin. With FSK = Low the switch at pin XTO2 is closed, with FSK = High the switch is open. To achieve a faster start-up of the crystal oscillator, the FSK pin should be High during start-up of the XTO because the series resistance of the resonator seen from pin XTO1 is lower if the switch is off. The different modes of the ATA5756/ATA5757 are listed in Table 4-1, the corresponding current consumption values can be found in the table "Electrical Characteristics" on page 15. Table 4-1.
ASK Pin Low Low Low High High Low/High High
ATA5756/ATA5757 Modes
FSK Pin Low Low High Low High High Low/High ENABLE Pin Low/open High High/open High/open High/open Low Low Mode Power-down mode, FSK switch High Z Power-up, PA off, FSK switch Low Z Power-up, PA off, FSK switch High Z Power-up, PA on, FSK switch Low Z Power-up, PA on, FSK switch High Z Idle mode, FSK switch High Z Idle mode, FSK switch High Z
5
4702J-RKE-09/08
4.1
4.1.1
Transmission with ENABLE = open
ASK Mode The ATA5756/ATA5757 is activated by ENABLE = open, FSK = High, ASK = Low. The microcontroller is then switched to external clocking. After typically 0.6 ms, the CLK driver is activated automatically (i.e., the microcontroller waits until the XTO and CLK are ready). After another time period of 250 s, the PLL is locked and ready to transmit. The output power can then be modulated by means of pin ASK. After transmission, ASK is switched to Low and the microcontroller returns back to internal clocking. Then, the ATA5756/ATA5757 is switched to power-down mode with FSK = Low. Figure 4-1. Timing ASK Mode with ENABLE not Connected to the Microcontroller
TXTO FSK > 250 s
ASK
CLK Power-down Power-up, PA off Power-up, PA on (High) Power-up, PA off (Low) Power-down
4.1.2
FSK Mode The ATA5756/ATA5757 is activated by FSK = High, ASK = Low. The microcontroller is then switched to external clocking. After typically 0.6 ms, the CLK driver is activated automatically (i.e., the microcontroller waits until the XTO and CLK are ready. After another time period of 250 s, the PLL is locked and ready to transmit. The power amplifier is switched on with ASK = H. The ATA5756/ATA5757 is then ready for FSK modulation. The microcontroller starts to switch on and off the capacitor between the crystal load capacitor and GND by means of pin FSK, thus, changing the reference frequency of the PLL. IF FSK = L the output frequency is lower, if FSK = H output frequency is higher. After transmission, FSK stays High and ASK is switched to Low and the microcontroller returns back to internal clocking. Then, the ATA5756/ATA5757 is switched to power-down mode with FSK = Low. Figure 4-2. Timing FSK Mode with ENABLE not Connected to the Microcontroller
TXTO FSK > 250 s
ASK
CLK Power-down Power-up, PA off Power-up, Power-up, PA off PA on (fRF = High) (fRF = Low) Power-down
6
ATA5756/ATA5757
4702J-RKE-09/08
ATA5756/ATA5757
4.2
4.2.1
Transmission with ENABLE = High
FSK Mode The ATA5756/ATA5757 is activated by ENABLE = High, FSK = High and ASK = Low. The microcontroller is then switched to external clocking. After typically 0.6 ms, the CLK driver is activated automatically (i.e., the microcontroller waits until the XTO and CLK are ready). After another time period of 250 s, the PLL is locked and ready to transmit. The power amplifier is switched on with ASK = H. The ATA5756/ATA5757 is then ready for FSK modulation. The microcontroller starts to switch on and off the capacitor between the crystal load capacitor and GND by means of pin FSK, thus, changing the reference frequency of the PLL. IF FSK = L the output frequency is lower, if FSK = H output frequency is higher. After transmission, ASK is switched to Low and the microcontroller returns back to internal clocking. Then, the ATA5756/ATA5757 is switched to power-down mode with ENABLE = Low and FSK = Low. Figure 4-3. Timing FSK Mode with ENABLE Connected to the Microcontroller
TXTO ENABLE > 250 s
FSK
ASK
CLK Power-down Power-up, PA off Power-up, Power-up, PA on PA off (fRF = High) (fRF = Low) Power-down
4.2.2
ASK Mode The ATA5756/ATA5757 is activated by ENABLE = High, FSK = High and ASK = Low. After activation the microcontroller is switched to external clocking. After typically 0.6 ms, the CLK driver is activated automatically (the microcontroller waits until the XTO and CLK are ready). After another time period of 250 s, the PLL is locked and ready to transmit. The output power can then be modulated by means of pin ASK. After transmission, ASK is switched to Low and the microcontroller returns back to internal clocking. Then, the ATA5756/ATA5757 is switched to power-down mode with ENABLE = Low and FSK = Low.
7
4702J-RKE-09/08
Figure 4-4.
Timing ASK Mode with ENABLE Connected to the Microcontroller
TXTO > 250 s
ENABLE
FSK
ASK
CLK Power-down Power-up, PA off Power-up, Power-up, PA on PA off (High) (Low) Power-down
4.3
Accuracy of Frequency Deviation
The accuracy of the frequency deviation using the XTAL pulling method is about 20% if the following tolerances are considered. One important aspect is that the values of C0 and CM of typical crystals are strongly correlated which reduces the tolerance of the frequency deviation. Figure 4-5. Tolerances of Frequency Modulation
~
VS C Stray
XTAL
CM
LM C0
RS
C4 C5 CSwitch
Using a crystal with a motional capacitance of CM = 4.37 fF 15%, a nominal load capacitance of C LNOM = 18 pF and a parallel capacitance of C 0 = 1.30 pF correlated with C M results in C0 = 297 x CM (the correlation has a tolerance of 10%, so C0 = 267 to 326 x CM). If using the internal FSK switch with CSwitch = 0.9 pF 20% and estimated parasites of CStray = 0.7 pF 10%, the resulting C4 and C5 values are C4 = 10 pF 1% and C5 = 15 pF 1% for a nominal frequency deviation of 19.3 kHz with worst case tolerances of 15.8 kHz to 23.2 kHz.
8
ATA5756/ATA5757
4702J-RKE-09/08
~
Crystal equivalent circuit
ATA5756/ATA5757
4.4 Accuracy of the Center Frequency
The imaginary part of the impedance in large signal steady state oscillation IMXTO, seen into the pin 7 (XTO1), causes some additional frequency tolerances, due to pulling of the XTO oscillation frequency. These tolerances have to be added to the tolerances of the crystal itself (adjustment tolerance, temperature stability and ageing) and the influence to the center frequency due to tolerances of C 4, C5, CSwitch and CStray. The nominal value of IMXTO = 110 , CSwitch and CStray should be absorbed into the C4 and C5 values by using a crystal with known frequency and choosing C4 and C5, so that the XTO center frequency equals the crystal frequency, and the frequency deviation is as expected. Then, from the nominal value, the IMXTO has 90 tolerances, using the pulling formula P = -IMXTO x CM x x fXTO with fXTO = 13.56 MHz and CM = 4.4 fF an additional frequency tolerance of P = 16.86 ppm results. If using crystals with other CM the additional frequency tolerance can be calculated in the same way. For example, a lower C M = 3.1 fF will reduce the frequency tolerance to 11.87 ppm, where a higher C M = 5.5 fF increases the tolerance to 21.07 ppm.
4.5
CLK Output
An output CLK signal of 1.64 MHz (ATA5756 operating at 315 MHz) and 1.69 MHz (ATA5757 operating at 433.92 MHz) is provided for a connected microcontroller. The delivered signal is CMOS-compatible with a High and Low time of >125 ns if the load capacitance is lower than 20 pF. The CLK output is Low in power-down mode due to an internal pull-down resistor. After enabling the PLL and XTO the signal stays Low until the amplitude of the crystal oscillator has reached 35% to 80% of its amplitude. Then, the CLK output is activated synchronously with its output signal so that the first period of the CLK output signal is a full period.
4.5.1
Clock Pulse Take-over by Microcontroller The clock of the crystal oscillator can be used for clocking the microcontroller. Atmel's ATARx9x microcontroller family provides the special feature of starting with an integrated RC oscillator to switch on the ATA5756/ATA5757's external clocking and to wait automatically until the CLK output of the ATA5756/ATA5757 is activated. After a time period of 250 s the message can be sent with crystal accuracy. Output Matching and Power Setting The output power is set by the load impedance of the antenna. The maximum output power is achieved with a load impedance of ZLoad, opt = 380 + j340 (ATA5756) at 315 MHz and ZLoad, opt = 280 + j310 (ATA5757) at 433.92 MHz. A low resistive path to VS is required to deliver the DC current (see Figure 4-6 on page 10). The power amplifier delivers a current pulse and the maximum output power is delivered to a resistive load if the 0.66 pF output capacitance of the power amplifier is compensated by the load impedance. At the ANT1 pin, the RF output amplitude is about VS - 0.5 V. The load impedance is defined as the impedance seen from the ATA5756's ANT1, ANT2 into the matching network. Do not mix up this large-signal load impedance with a small-signal input impedance delivered as an input characteristic of RF amplifiers. The latter is measured from the application into the IC instead of from the IC into the application for a power amplifier.
4.5.2
9
4702J-RKE-09/08
The 0.66 pF output capacitance absorbed into the load impedance a real impedance of 684 (ATA5756) at 315 MHz and 623 (ATA5757) at 433.92 MHz should be measured with a network analyses at pin 5 (ANT1) with the ATA5756/ATA5757 soldered, an optimized antenna connected and the power amplifier switched off. Less output power is achieved by lowering the real parallel part where the parallel imaginary part should be kept constant. Lowering the real part of the load impedance also reduces the supply voltage dependency of the output power. Output power measurement can be done with the circuit as shown in Figure 4-6. Please note that the component values must be changed to compensate the individual board parasitics until the ATA5756/ATA5757 has the right load impedance. Also, the damping of the cable used to measure the output power must be calibrated. Figure 4-6. Output Power Measurement ATA5756/ATA5757
VS C1 = 1n
ANT1 Z Lopt ANT2
~
L1 = 68 nH/ 39 nH Z = 50 C2 = 2.2 pF/1.8 pF
Power meter Rin 50
~
Table 4-2 and Table 4-3 show the output power and the supply current versus temperature and supply voltage. Table 4-2. Output Power and Supply Current versus Temperature and Supply Voltage for the ATA5756 with ZLoad = 380 + j340 (Correlation Tested)
VS = 2.0 V (dBm/mA) 3.1 1.5 / 7.2 3.0 1.5 / 7.5 3.0 1.5 / 7.5 2.5 1.5 / 7.6 VS = 3.0 V (dBm/mA) 6.1 +2/-3 / 7.7 6.0 2 / 8.1 5.8 +2/-3 / 8.2 5.5 +2/-3 / 8.2 VS = 3.6 V (dBm/mA) 7.1 +2/-3 / 7.9 7.4 2 / 8.3 7.2 +2/-3 / 8.5 6.5 +2/-3 / 8.5
Ambient Temperature Tamb = -40C Tamb = +25C Tamb = +85C Tamb = +125C
Table 4-3.
Output Power and Supply Current versus Temperature and Supply Voltage for the ATA5757 with ZLoad = 280 + j310 (Correlation Tested)
VS = 2.0 V (dBm/mA) 3.3 1.5 / 7.6 3.0 1.5 / 8.0 2.8 1.5 / 8.0 2.7 1.5 / 8.1 VS = 3.0 V (dBm/mA) 6.2 +2/-3 / 8.1 6.0 2 / 8.5 5.7 +2/-3 / 8.6 5.5 +2/-3 / 8.7 VS = 3.6 V (dBm/mA) 7.1 +2/-3 / 8.4 7.5 2 / 8.8 6.8 +2/-3 / 8.8 6.6 +2/-3 / 8.9
Ambient Temperature Tamb = -40C Tamb = +25C Tamb = +85C Tamb = +125C
10
ATA5756/ATA5757
4702J-RKE-09/08
ATA5756/ATA5757
4.6 Application Circuits
For the supply voltage blocking capacitor C3, a value of 68 nF/X7R is recommended (see Figure 4-7 on page 12 and Figure 4-8 on page 13). C1 and C2 are used to match the loop antenna to the power amplifier. For C2, two capacitors in series should be used to achieve a better tolerance value and to enable it to realize ZLoad,opt by using capacitors with standard values. Together with the pins of ATA5756 and the PCB board wires, C1 forms a series resonance loop that suppresses the 1st harmonic, hence the position of C1 on the PCB is important. Normally, the best suppression is achieved when C1 is placed as close as possible to the pins ANT1 and ANT2. The loop antenna should not exceed a width of 1.5 mm, otherwise the Q-factor of the loop antenna is too high. L1 (50 nH to 100 nH) can be printed on the PCB. C4 should be selected so that the XTO runs on the load resonance frequency of the crystal. Normally, a value of 10 pF results in a 12 pF load-capacitance crystal due to the board parasitic capacitances and the inductive impedance of the XTO1 pin.
11
4702J-RKE-09/08
Figure 4-7.
ASK Application Circuit
S1
BPXY
ATARx9x
VDD
1
VSS
20
VS
S2
BPXY
BPXY
OSC1
BPXY
7
ATA5756/ATA5757
Power up/down CLK
f 8
EN
ENABLE
1
10 f
ASK
24/ 32
GND
2
OR FSK
9 C3
VS
PFD
3
C2 ANT2 CP Ampl. OK
8
VS XTO1
XTAL
4
Loop Antenna
XTO LF
7 C4
C1
EN ANT1
XTO2
PA
5
L1
VCO PLL
6
VS
12
ATA5756/ATA5757
4702J-RKE-09/08
ATA5756/ATA5757
Figure 4-8. FSK Application Circuit
S1
BPXY
ATARx9x
VDD
1
VSS
20
VS
S2
BPXY
BPXY
OSC1
BPXY
7
ATA5756/ATA5757
Power up/down CLK
1
f 8
EN
ENABLE
10 f
ASK
24/ 32
GND
2
OR FSK
9 C3
VS
PFD
3
C2 ANT2 CP Ampl. OK
8
VS XTO1
XTAL
4
Loop Antenna
XTO LF
7
C1
EN ANT1
XTO2
PA
C5 C4
5
L1
VCO
6
PLL
VS
13
4702J-RKE-09/08
Figure 4-9.
VS
ESD Protection Circuit
ANT1
CLK
ASK
FSK
ANT2
XTO2
XTO1
ENABLE
GND
5. Absolute Maximum Ratings
Parameters Supply voltage Power dissipation Junction temperature Storage temperature Ambient temperature Ambient temperature in power-down mode for 15 minutes without damage with VS 3.2 V VENABLE < 0.25 V or ENABLE is open, VASK < 0.25 V, VFSK < 0.25 V Input voltage Note: Symbol VS Ptot Tj Tstg Tamb1 Tamb2 VmaxASK -0.3 -55 -55 Minimum Maximum 5 100 150 125 125 Unit V mW C C C
175 (VS + 0.3)(1)
C
V
1. If VS + 0.3 is higher than 3.7 V, the maximum voltage will be reduced to 3.7 V.
6. Thermal Resistance
Parameters Junction ambient Symbol RthJA Value 170 Unit K/W
14
ATA5756/ATA5757
4702J-RKE-09/08
ATA5756/ATA5757
7. Electrical Characteristics
VS = 2.0 V to 3.6 V, Tamb = -40C to 125C unless otherwise specified. Typical values are given at VS = 3.0 V and Tamb = 25C. All parameters are referred to GND (Pin 9).
CM = 4.37 fF, C0 = 1.3 pF, CLNOM = 18 pF, C4 = 10 pF, C5 = 15 pF and RS 60 Parameters Supply current, power-down mode Test Conditions VENABLE < 0.25 V or ENABLE is open, VASK < 0.25 V, VFSK < 0.25 V Tamb = 25C Tamb = -40C to +85C Tamb = -40C to +125C VENABLE < 0.25 V, VS 3.2 V ASK,FSK can be Low or High VS 3.2 V, VFSK > 1.7 V, VASK < 0.25 V ENABLE is open VS 3.2 V, CCLK 10 pF VFSK > 1.7 V, VASK > 1.7 V ENABLE is open Symbol Min. Typ. Max. Unit
IS_Off
1
100 350 7,000 100
nA nA nA A mA
Supply current, idle mode Supply current, power-up, PA off, FSK switch High Z Supply current, power-up, PA on, FSK switch High Z
IS_IDLE IS 3.6
4.6
IS_Transmit1 8.1 8.5 9.8 10.5 mA mA
ATA5756 ATA5757
VS 3.2 V, CCLK 10 pF VFSK< 0.25 V, VASK > 1.7 V ENABLE is open
Supply current, power-up, PA on, FSK Low Z
IS_Transmit2 8.4 8.8 10.2 11.0 mA mA
ATA5756 ATA5757
VS = 3.0 V, Tamb = 25C, f = 315 MHz for ATA5756, ZLoad, opt = (380 + j340) f = 433.92 MHz for ATA5757, ZLoad, opt = (280 + j310) Tamb = -40C to +125C, VS = 2.0 V to 3.2 V fCLK = fXT0/8 Load capacitance at pin CLK 20 pF f0 fCLK f0 fXT0 other spurious are lower With 50 matching network according to Figure 4-6 on page 10 2nd 3rd fXTO = f0/24 ATA5756 fXTO = f0/32 ATA5757 fXTAL = resonant frequency of the XTAL, CM = 4.37 fF, load capacitance selected accordingly Tamb = -40C to +85C Tamb = -40C to +125C
Output power
POut
4
6
8
dBm
Output power for the full temperature and supply voltage range
POut
1
8.2
dBm
Spurious emission
Spour
-42 -60
dBc
Harmonics
-16 -15
dBc dBc
Oscillator frequency XTO (= phase comparator frequency)
fXTO -14.0 -17.5 fXTAL fXTAL +14.0 +17.5 ppm ppm
15
4702J-RKE-09/08
7. Electrical Characteristics (Continued)
VS = 2.0 V to 3.6 V, Tamb = -40C to 125C unless otherwise specified. Typical values are given at VS = 3.0 V and Tamb = 25C. All parameters are referred to GND (Pin 9).
CM = 4.37 fF, C0 = 1.3 pF, CLNOM = 18 pF, C4 = 10 pF, C5 = 15 pF and RS 60 Parameters Imaginary part of XTO1 Impedance in steady state oscillation Real part of XTO1 impedance in small signal oscillation Test Conditions Since pulling P is P = -IMXTO x CM x x fXTO fXTO can be calculated out of IMXTO with CM = 4.37 fF This value is important for crystal oscillator start-up Time between ENABLE of the IC with FSK = H and activation of the CLK output. The CLK is activated synchronously to the output frequency if the current through the XTAL has reached 35% to 80% of its maximum amplitude. Crystal parameters: CM = 4.37 fF, C0 = 1.3 pF, CLNOM = 18 pF, C4 = 10 pF, C5 = 15 pF, RS 60 Current flowing through the crystal in steady state oscillation (peak-to-peak value) Time between the activation of CLK and when the PLL is locked (transmitter ready for data transmission) 25 kHz distance to carrier at 1 MHz at 36 MHz ATA5756 ATA5757 ATA5756 ATA5757 CLoad 20 pF, High = 0.8 x Vs, Low = 0.2 x VS, fCLK < 1.7 MHz For proper detection of the XTO amplitude Symbol IMXTO Min. j20 Typ. j110 Max. j200 Unit
REXTO
-650
-1100
Crystal oscillator start-up time
TXTO
0.6
1.4
ms
XTO drive current
IDXTO
300
App
Locking time of the PLL PLL loop bandwidth In loop phase noise PLL Phase noise VCO Frequency range of VCO Clock output frequency (CMOS microcontroller compatible) Clock output minimum High and Low time Series resonance resistance of the resonator seen from pin XTO1 Capacitive load at Pin XTO1 FSK modulation frequency rate FSK switch OFF resistance FSK switch OFF capacitance FSK switch ON resistance ASK modulation frequency rate
TPLL fLoop_PLL LPLL Lat1M Lat36M fVCO fCLK TCLKLH Rs_max CL_max 125 310 432 f0/192 f0/256 250 -85 -90 -121
250
s kHz
-76 -84 -115 317 448
dBc/Hz dBc/Hz dBc/Hz MHz MHz MHz ns
150 5 0 50 0.75 0.9 130 0 1.1 175 20 20
pF kHz k pF kHz
This corresponds to 20 kBaud in Manchester coding and 40 kBaud in NRZ coding High Z High Z capacitance Low Z Duty cycle of the modulation signal = 50%, this corresponds to 20 kBaud in Manchester coding and 40 kBaud in NRZ coding
fMOD_FSK RSWIT_OFF CSWIT_OFF RSWIT_ON fMOD_ASK
16
ATA5756/ATA5757
4702J-RKE-09/08
ATA5756/ATA5757
7. Electrical Characteristics (Continued)
VS = 2.0 V to 3.6 V, Tamb = -40C to 125C unless otherwise specified. Typical values are given at VS = 3.0 V and Tamb = 25C. All parameters are referred to GND (Pin 9).
CM = 4.37 fF, C0 = 1.3 pF, CLNOM = 18 pF, C4 = 10 pF, C5 = 15 pF and RS 60 Parameters ASK input Test Conditions Low level input voltage High level input voltage Input current high Low level input voltage High level input voltage Input current high Low level input voltage High level input voltage Input current high Input current Low Symbol VIl VIh IIn VIl VIh IIn VIl VIh IInh IInl Min. 1.7 Typ. Max. 0.25 VS 30 0.25 VS 30 0.25 VS 40 40 Unit V V A V V A V V A A
FSK input
1.7
ENABLE input
1.7 -40 -40
17
4702J-RKE-09/08
8. Ordering Information
Extended Type Number ATA5756-6DQY ATA5756-6DPY ATA5757-6DQY ATA5757-6DPY Package TSSOP10 TSSOP10 Remarks Pb-free Pb-free
9. Package Information TSSOP10
Package: TSSOP 10 (acc. to JEDEC Standard MO-187) Dimensions in mm Not indicated tolerances 0.05
1.1 max
0.850.1
30.1
30.1
0.5 nom. 4 x 0.5 = 2 nom. 10 9 8 7 6
3.80.3 4.90.1
technical drawings according to DIN specifications
Drawing-No.: 6.543-5095.01-4 12345 Issue: 3; 16.09.05
18
ATA5756/ATA5757
4702J-RKE-09/08
0.15
0.25
ATA5756/ATA5757
10. Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4702J-RKE-07/08 History * Put datasheet in a new template * Page1: PB-free logo deleted * Page 18: Ordering Information changed * Put datasheet in a new template * First page: Pb-free logo added * Page 18: Ordering Information and package drawing changed * Electrical Characteristics table, page 15, row "Output power for the full...". -> maximum value changed * Electrical Characteristics table, page 15, row "Output power variation...". -> the word "variation" deleted * Preliminary deleted * Abs. Max. Ratings table (page 14): row "Input voltage" added * Abs. Max. Ratings table (page 14): table note 1 added * El. Char. table (page 17): rows "ASK input", "FSK input", "ENABLE input" maximum values changed
4702I-RKE-11/05
4702H-RKE-09/04 4702G-RKE-08/04 4702F-RKE-08/04
4702E-RKE-07/04
19
4702J-RKE-09/08
Headquarters
Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600
International
Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581
Product Contact
Web Site www.atmel.com Technical Support Enter Product Line E-mail Sales Contact www.atmel.com/contacts
Literature Requests www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
(c) 2008 Atmel Corporation. All rights reserved. Atmel(R), logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
4702J-RKE-09/08

▲Up To Search▲

Price & Availability of ATA5756-6DPY

	To Download ATA5756-6DPY Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .